Home / / How do I arm and disarm my Ademco 4110 DL or 4110XM system?

How do I arm and disarm my Ademco 4110 DL or 4110XM system?

THIS INFORMATION IS TAKEN DIRECTLY FROM THE MANUAL FOR THIS ALARM SYSTEM.

Arming Perimeter Only

With Entry Delay On

Use this key when you are staying inside, but expect someone to use an entry/exit door later.

    1. Enter your security code and press the STAY key.
    2. The keypad will beep three times and will display the armed message. The red ARMED indicator will light.
    3. The system will arm. An alarm will sound immediately if a protected perimeter window or non-entry/exit door is then opened, but you may otherwise move freely throughout the premises.

Later arrivals can enter through an entry/exit door without causing an alarm, but they must disarm the system within the entry delay period to avoid sounding an alarm.

Note: BEFORE ARMING close all doors and windows.

Arming Perimeter Only

With Entry Delay Off

Use this key when you are staying inside, but do not expect anyone to use an entry/exit door.

    1. Enter your security code and press the INSTANT key.
    2. The keypad will beep three times and will display the armed message. The red ARMED indicator will light.
    3. The system will arm. An alarm will sound immediately if a protected perimeter window or non-entry/exit door is then opened, but you may otherwise move freely throughout the premises.

An alarm will sound immediately if anyone opens an entry/exit door.

Note: BEFORE ARMING close all doors and windows.

Arming All Protection

With Entry Delay On

Use this key when no one will be staying inside.

    1. Enter your security code and press the AWAY key.
    2. The keypad will beep twice and will display the armed message. The red ARMED indicator will light.
    3. You may leave through an entry/exit door during the exit delay period without causing an alarm.
    After exit delay, the system arms and will sound an alarm if a protected window or non-entry/exit door is then opened, or if any movement is detected inside your premises.

You may re-enter through an entry/exit door, but must disarm the system within the entry delay period to avoid an alarm.
Note: BEFORE ARMING close all doors and windows.

Arming All Protection

With Entry Delay Off

Use this key when the premise will be vacant for extended periods of time such as vacations – when no one will be moving through protected interior areas.

    1. Enter your security code and press the MAXIMUM key.
    2. The keypad will beep twice and will display the armed message. The red ARMED indicator will light.
    3. You may leave through an entry/exit door during the exit delay period without causing an alarm.
    After exit delay, the system arms and will sound immediately if any protected door or window is opened, or if any movement is detected inside your premises.

An alarm will sound immediately when someone re-enters.

Disarming the System and Silencing Alarms

The OFF key is used to disarm the system and to silence alarm and trouble sounds.

TO DISARM THE SYSTEM
Enter your security code and press the OFF key. The “Ready” message will be displayed, and the keypad will emit a single tone to confirm that the system is disarmed.

TO SILENCE A BURGLARY ALARM (*see important notice below*)
Enter your security code and press the OFF key to silence the alarm (or warning tones of a Memory of Alarm). Note the zone in alarm on the keypad display, and make that zone intact (close door, window, etc). Now enter the security code plus OFF sequence again to clear the keypad’s Memory of Alarm display. If the display will not clear and does not provide a “Ready” message, notify your alarm company.

To Silence a Fire Alarm
Simply press the OFF key (the security code is not needed to silence FIRE alarms). To then clear the keypad’s Memory of Alarm display, enter your security code and press the OFF key.

*IMPORTANT NOTICE*
If you return and the main burglary sounder is on: DO NOT ENTER, but CONTACT THE POLICE from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off: the keypad will beep rapidly upon your entering, indicating that an alarm has occurred during your absence (the Memory of Alarm feature). LEAVE IMMEDIATELY AND CONTACT THE POLICE from a nearby safe location. WHEN SAFE TO DO SO, re-enter and follow the procedure for silencing an alarm.